Our MEP consultants plan, model, and coordinate electrical, plumbing, and firefighting systems for efficient commercial operations.
Our MEP consultants plan, model, and coordinate electrical, plumbing, and firefighting systems for efficient commercial operations.
.png){kind=logo}
How to meter a commercial building usefully — what to sub-meter, why a single incoming meter tells you nothing, and turning data into reduced consumption.
How a server room's services are designed — heat load, dedicated cooling, redundancy, power backup, fire suppression and the monitoring that makes it safe.
What a BMS monitors and controls, why most deliver less than promised, the difference between monitoring and control, and what to specify to get value.
How a commercial HVAC system is designed — load calculation, system selection, air distribution, fresh air provision and controls — and what gets missed.
How backup power is designed for a commercial building — defining the essential load, sizing DG and UPS, segregating circuits, and the siting constraints.
HT and LT panels, power distribution, wiring, earthing and small power for commercial and industrial buildings — installed, tested and handed over.
Addressable fire alarm, smoke and heat detection, manual call points and PA integration for offices, hospitals and industrial buildings.
Fire hydrant, wet riser, sprinkler and pump room installation for commercial and industrial buildings, with a dedicated 35-member firefighting team.
MEP for hospitals and clinics — OT, ICU, emergency, diagnostics and patient rooms — where air, power and water failures carry clinical consequences.
CCTV, access control, public address, and building management interfaces for offices, hospitals and industrial sites — installed and integrated.
Structured cabling, network racks, data outlets and containment for offices — designed around the desk layout and certified on handover.
Water supply, drainage, sanitary fixtures and pumping for commercial, industrial and hospitality buildings — installed and pressure tested.
Background reading on the decisions this service involves — written from what goes wrong on site, with the standards named on the page.
The electrical chain in an office or factory, link by link: sanctioned load, HT or LT supply, panels, cables, backup, earthing, inspection and handover records.
GuideHow GMP shapes a pharma plant before a wall goes up: zoning, people and material flows, cleanable finishes, pressure cascades and DQ, IQ, OQ, PQ records.
ComparisonSingle-contract design-build against separate designer and contractor appointments: programme, accountability, cost certainty and where each route fails.
ComparisonDiesel generator against UPS in a commercial building: transfer time, runtime, load types, space, and why most buildings need both rather than one.
ComparisonGlazed partitions against stud-and-board walls in an office fit-out: acoustic performance, daylight, services routing, cost drivers and reuse at the next churn.
MEP stands for mechanical, electrical and plumbing: the building services that make a space usable. In practice it covers power distribution, lighting, plumbing and drainage, firefighting and fire detection, and often low-voltage systems such as data cabling and access control. Air conditioning is sometimes grouped under MEP and sometimes treated as a separate HVAC package.
Because several services share the same ceiling void and must be installed in order. Without a coordinated drawing that resolves where each duct, pipe and cable tray sits, clashes are found on site and work is removed and redone. Coordination drawings for the execution teams are one of our MEP deliverables for exactly this reason.
A load calculation works out how much electrical capacity a space actually needs from its lighting, equipment, air conditioning and other connected loads. It sizes cables, distribution boards and backup power correctly, and it shows early whether the building's existing supply is enough. Estimating from a rule of thumb instead is how installations end up undersized or needlessly expensive.
Yes, significantly. Every enclosed room needs its own lighting circuits and controls, changes where sprinklers and detectors sit, and affects power and data positions. A layout with many small rooms is a larger MEP job than the same floor left open, which is why the layout should be settled before MEP design is finalised.
Testing confirms each piece of equipment works; commissioning confirms the whole system performs as designed once everything is connected. It covers electrical tests, checking that controls behave as intended, and the interfaces between systems such as the fire alarm and air handling. Commissioning records with measured results should be part of the handover documentation.
We design and deliver HVAC systems that improve indoor air quality, comfort, and energy performance for commercial spaces.
We deliver turnkey office design & build solutions—strategy, space planning, interiors, and execution—so teams move into fully operational workspaces faster.
Our interior fit-out teams deliver high-quality finishes, partitions, joinery, and on-site coordination for commercial workspaces.
Talk to our specialists for a tailored design, MEP, or fit-out roadmap.
Tell us what you are planning. Message our team on WhatsApp, call us, or leave your number and we will call you back.