# Slab Edge Firestop: Sealing the Gap Behind a Curtain Wall

> A slab edge firestop is the fire-resistant seal in the gap between the back of a curtain wall and the edge of each floor slab. Without it that continuous perimeter gap is an open vertical route for fire and smoke between floors, bypassing the floor's own fire resistance entirely.

## Why it matters on a project

A building's floors are a large part of its compartmentation — each slab is
meant to hold fire on the storey where it starts.

A curtain wall introduces a continuous gap at every floor, running the full
perimeter of the building. Unsealed, that gap defeats the floor's fire
resistance completely, and it does so at every level simultaneously. It is one
of the few details where a small, hidden and inexpensive item carries
disproportionate consequence.

## What the joint has to accommodate

| Demand | Why it exists |
| --- | --- |
| Fire and smoke resistance | The gap bypasses the floor's compartmentation |
| Vertical movement | Floors deflect; facade and structure move differently |
| Horizontal movement | Thermal expansion of the facade, building sway |
| Construction tolerance | The real gap varies from the drawn gap |
| Compatibility with the facade | The system is tested with a particular wall behind it |

## The "system, not product" point

This is the single most important thing to understand about slab edge
firestopping.

The tested performance belongs to a **combination**: a particular facade
construction, a stated gap width, insulation of a specified density and
thickness compressed by a specified amount, particular fixings, and a specified
smoke seal. Change any of those and the test evidence no longer describes what
is installed.

That is why "we used mineral wool" is not an answer, and why the submittal
should be a system with test documentation matching the installed condition.

Testing is addressed by **ASTM E2307** for perimeter fire barrier systems and
**EN 1366-4** for linear joint seals.

## Common mistakes

- **Treating it as insulation rather than a tested system.** The most common and
  most serious error on this detail.
- **Substituting components on site.** Different density, thickness or
  compression means different performance.
- **Leaving it to the fit-out contractor.** Access to the perimeter gap is gone
  once the interior starts.
- **Not matching the gap width to the tested range.** Real gaps vary; the system
  must cover the actual dimension.
- **Ignoring the smoke seal.** Fire resistance without smoke sealing leaves the
  route that actually harms people first.
- **No inspection record.** Once the perimeter is closed, nobody can verify what
  is behind it.

## Standards referenced

Compartmentation provisions in **NBC 2016, Part 4**; perimeter fire barrier
system testing to **ASTM E2307**; linear joint seal fire resistance testing to
**EN 1366-4**. The requirement for a specific building, and the acceptability of
a proposed system, must be determined by the project's fire consultant and the
authority having jurisdiction.

## Frequently asked questions

### Why does the gap exist at all?

Because a curtain wall hangs outside the structure rather than sitting on it, so there is necessarily a space between the back of the facade and the slab edge. That space is also needed for tolerance and for movement, since the facade and the structure move independently. The gap is a consequence of how curtain walling works, not a construction defect.

### What makes this joint difficult?

It has to do two contradictory things at once — stay sealed against fire and smoke, and accommodate movement. The building moves under wind and thermal change, floors deflect, and the facade expands and contracts. A rigid seal that resists fire perfectly but cracks under movement has failed; so has a flexible seal that cannot hold back fire. This is why it is engineered as a tested system.

### Is it just insulation stuffed into the gap?

No, and treating it that way is a common and serious error. A perimeter fire barrier is a tested assembly with specified components — typically a mineral wool of defined density and thickness compressed by a stated amount, secured in a specified way, often with a sprayed or applied smoke seal, and detailed to work with the particular curtain wall behind it. Substituting any component can invalidate the tested performance.

### How is it tested?

As a system, not as a product. ASTM E2307 covers fire resistance testing of perimeter fire barrier systems using an intermediate-scale multi-storey apparatus, and EN 1366-4 addresses linear joint seals. The test evidence relates to a specific combination of facade, gap width, insulation and seal, so the documentation should match what is actually being installed.

### What is required on a specific building?

That depends on the building's height, occupancy and the compartmentation strategy, which are determined under NBC 2016 Part 4 together with applicable state and local rules. The requirement and the acceptable system for a given project must be established by the project's fire consultant and the authority having jurisdiction — it is not a specification that transfers between buildings.

### When does it get installed?

Progressively, as the facade goes up, floor by floor. It is genuinely difficult to install well after the facade is complete and the interior is fitting out, because access to the perimeter gap disappears. Programming it with the facade rather than with the fit-out is one of the practical things that most affects whether it is done properly.

## Sources

- [NBC 2016, Part 4](https://www.bis.gov.in/standards/national-building-code/?lang=en) — Fire and life safety — compartmentation
- [ASTM E2307](https://www.astm.org/products-services/standards-and-publications.html) — Fire resistance of perimeter fire barrier systems
- [EN 1366-4](https://standards.cencenelec.eu/ords/f?p=CEN:105) — Fire resistance tests for service installations — linear joint seals

---

Source: https://hagerstone.com/glossary/slab-edge-firestop